Ultimate FAQ: Garage Flooring Tiles & LED Light Systems

Summary

 

• Tiles: Rigid polypropylene (PP) modular tiles; choose vented for drainage, solid/3D for a clean, continuous look. Typical tile ≈ 40×40×1.8 cm (≈ 6.25 tiles/m²). Leave 5–10 mm expansion at walls.
  
  
• Install time: Single garage (~18 m²) 2–3.5 hrs; double (~36 m²) 4–6 hrs for most DIYers.
  
  
• Jacks: OK with a pad/puck to spread point loads.
  
  
• Lights: Go 6500K for crisp, true inspection. Target 400–600 lm/m² for wrenching; 700–1000+ lm/m² for detailing/content. Flush mount for low ceilings, suspension for 3 m+.
  
  
• Power: Plug-and-play = DIY; hardwiring should be done by a licensed electrician.

 

 

---

 

Garage Flooring Tiles (FAQ)

 

1) What are modular garage tiles made of?

All tiles are made out of raw polypropylene (PP): rigid, UV/heat resistant, and suitable for heavy rolling loads. You may find other companies selling PVC but it is not the perfect solution. PP handles heavy loads, chemicals and heat way better and is the perfect choice for this scenario. They can withstand up to 20 tons per tile, -40 to 120 degrees celsius and colors would not fade after a few months.

 

2) Vented vs Solid: how do I choose?

• Vented: Channels drain water and trap debris below the surface—best for wash bays, snow/rain entries, and wet work. (detailing, wrapping, tinting, PPF)

• Solid: A continuous, premium look with firm contact—great for workshops,  and dry work zones.

   

  Many customers mix surfaces by zone.

 

3) How many tiles do I need?

Use 6.25 tiles per m² as a quick rule for ~40×40 cm tiles. Add 5–10% overage for cuts, borders, and color patterns.

 

4) What tools do I need?

Rubber mallet, tape measure, square, marker, utility knife (small trims), fine-tooth circular saw or jigsaw for cuts (cut from the underside), eye/ear/hand protection, broom/vacuum (leaf blower optional).

 

5) How long will installation take?

Single bay (~18 m²): 2–3.5 hours. Double (~36 m²): 4–6 hours. Plan extra time for complex borders or lots of cuts.

 

6) Do I need glue or underlayment?

No. Tiles are a floating, interlocking system—no glue, no fumes, no cure time.

7) Can I use a jack or jack stands on tiles?

Yes—use a rigid pad (e.g., plywood puck) under jacks/stands to distribute point loads.

8) Will tiles handle hot tires and summer heat?

Yes—PP’s higher softening point resists hot-tire pickup. Coated with UV-protection, colors won't fade when exposed to constant sunlight. 

9) Can tiles go over cracked, painted or epoxied concrete?

Tiles bridge hairline cracks and mild unevenness. Level major steps first. You can install over sound, fully cured coatings, standard tiles, concrete and many others as long as the floor is flat.

10) Are tiles slippery?

Vented textures keep the walking surface grippy when wet; solid/3D textures provide traction in dry zones. Finished with a matte coat, our tiles would provide grip eve when wet and prevent you from slipping.

11) Are tiles okay with radiant floor heating?

Yes—vented tiles work best above radiant heat so warmth can vent upward evenly. They can withstand temperatures from -40 to 120 degrees celsius.

12) Can I use them outdoors?

Yes for many PP tiles. Ensure drainage, allow expansion, and consider lighter colors in direct sun.

13) Noise & comfort underfoot?

Rigid PP feels firm and can sound more “solid” than mats. Add anti-fatigue mats where you stand for long periods. The tiles make absolutely no sounds and noises when walking or driving on them.

14) What finishing pieces do I need?

Edges and ramps for door thresholds and exposed perimeters. They create safer, trip-free transitions and a clean finish.

15) Can I mix colors and surfaces?

Absolutely—use borders, lanes, or accent blocks to define parking, walkways, or photo zones.

16) Ongoing maintenance?

• Vented: blow/ vacuum debris from channels.

• Solid: mop with a neutral cleaner.

  Check edges/ramps seasonally and re-seat if needed.

 

17) Common mistakes to avoid

Skipping the wall gap; forcing misaligned interlocks; cutting from the top (cut from the underside); forgetting edges/ramps at door thresholds.

 

---

 

 

Garage LED Lights (FAQ)

 

1) Why 6500K for garages?

It’s a crisp, daylight-like white that reveals defects and keeps photos/video clean and consistent.

2) How bright should my space be (lumens per m²)?

• Storage/parking: 200–300 lm/m²

• Wrenching/general work: 400–600 lm/m²

• Detailing/content creation: 700–1000+ lm/m²

  Room reflectance and height affect final results; patterns and spacing matter.

 

3) Which pattern should I buy?

• Hex Models provide a symmetric and modern feel to your garage.
  
  
• Expo Models provide a more sophisticated look perfect for expositions and showrooms.
  
  
• PRO Models are for high end professionals and showrooms who need the extra bit of light and modern look. 

4) Flush vs suspended mounting?

• Flush: clean look, maximizes headroom—ideal for low ceilings.

• Suspension: balancing spread and uniformity in 3 m+ spaces or around door rails/lifts.

 

5) What’s the right ceiling height?

Everything works; choose flush below ~2.7 m and consider suspension for taller ceilings or when you need broader spread.

6) Will the lights flicker on camera?

Quality drivers minimize visible flicker. Do a quick 10-second test video before finalizing.

7) Can I dim the lights?

Unfortunately, no. Our models are non dimmable.

 

8) How do I power them—plug or hardwire?

Plug-and-play is DIY-friendly. Hardwiring to a dedicated circuit/switch should be done by a licensed electrician.

9) Energy use and efficiency

Large grids can be several hundred watts but deliver high lumens per watt compared with legacy fluorescents—bright, efficient light where you need it.

10) Are they suitable for wet areas?

Yes, with IP44, the lights can be in wet areas with no issues. Detailing, PPF garages, car washes etc. pose no problem for them. However, they are not waterproof and are only splash/moisture resistant.

11) Maintenance?

Dust rails gently; inspect connectors and cable tension every 6–12 months. Keep a small spares kit of rails/connectors.

12) Lifespan

Well-built systems typically run for many thousands of hours. Heat management and quality drivers prolong life. 2 years of warranty.

13) Motion sensors or smart controls?

Absolutely, they can be hardwired to whatever plug, power source and switch you like.

14) Safety basics

Power off at the breaker before work. Use proper anchors/fasteners for your ceiling type. Hardwiring = electrician.

15) Typical install time

As a guide: Hex & Expo models 90–120 min, PRO models 120–180 min for mounting (add 30–60 min for suspension setup). Electrical work timing varies by site.

16) Can I expand later?

Yes—most systems are modular. Plan cable pathways so future add-ons are easy.

17) Common mistakes to avoid

Mixing color temperatures, crowding rails near openers/door tracks, leaving slack cables visible, pointing alternates to switch-controlled outlets without checking load.